Most companies will not put a number on a webpage. We understand why, because every house is different and a bad guess creates a bad conversation later.
But you are trying to budget, not get a contract. So here is how gutter installation pricing actually works in this part of Washington, what moves the number up and down, and where homeowners tend to overspend.
Start with the honest structure
Gutter work is priced by the linear foot, plus downspouts, plus anything unusual about your house.
A typical single story home around Puget Sound has somewhere between 120 and 200 linear feet of gutter. A two story with a complex roofline can run 250 feet or more. That footage is the biggest single driver of your total, and it is the first thing an estimator measures.
Ballpark ranges
For seamless aluminum gutter, the material we install on nearly every home:
- Seamless aluminum gutter and downspouts, installed: $10 to $20 per linear foot
- Gutter covers added at the same time: $10 to $20 per linear foot
- Tear-off and haul away of old gutter: $5 to $10 per linear foot
Run that against your footage and a straightforward single story replacement lands somewhere around $1,800 to $6,000, tear-off included. A two story home or a complex roofline at 250 feet and up runs closer to $3,800 to $9,000.
Those are ranges, not quotes. The spread between the low end and the high end comes down to the factors below.
What pushes the price up
Height and access. A second story costs more than a first story, and a third story or a steep pitch costs more again. It is not the material, it is the setup time and the safety work.
Roofline complexity. Every corner, every valley, every dormer is a transition that has to be cut, sealed, and hung correctly. A simple rectangle house is cheaper per foot than the same footage wrapped around six corners.
Gutter size. Five inch is standard. Six inch costs more per foot and moves substantially more water, which matters on big roof planes in our rain.
Fascia repair. This is the one that surprises people. If the old gutters clogged and held water against the wood, the fascia underneath may be soft or rotted, and there is nothing to hang new gutter on until it is replaced. An estimator will flag it before the job, not after.
Downspout count and routing. More outlets means better drainage and more material. Running a downspout to a drain line or away from the foundation adds labor.
Material choice. Aluminum is the value standard. Copper is beautiful and costs several times more.
What brings the price down
Doing the whole house at once instead of in pieces, because mobilization and setup get spread across more footage. Straightforward single story access. Keeping the existing downspout locations where they are already working correctly.
And timing. Late summer and early fall are busy in this region because everyone remembers their gutters right before the rain. Booking in a slower stretch is sometimes easier to schedule, though it will not change the per-foot math much.
Where homeowners overspend
Repairing what needs replacing. Two or three service calls on a gutter system that is at the end of its life costs more than replacing it once. If your gutters are sagging in the middle, separating at the seams, or pulling away from the fascia, patching is renting time.
Buying covers before fixing capacity. If your gutters are undersized or short on downspouts, they will overflow in a hard rain with or without covers on them. Fix the sizing and the drainage first, then add covers.
Undersizing to hit a number. Going five inch on a large roof plane to save a few hundred dollars means overflow every winter, and the water lands next to your foundation. That is the expensive kind of savings.
Skipping the fascia. Hanging new gutter on soft wood means it pulls loose, and then you are paying for the same run twice.
What you should get for the money
A written estimate that lists footage, gutter size, downspout count, and any fascia work as separate lines, so you can compare bids honestly. Seamless gutter formed on site rather than sectional pieces joined in your yard. Hangers spaced correctly for our rain and snow load, not stretched out to save material.
Correct discharge, meaning water leaves the house instead of pooling at the foundation. And a warranty in writing. Ours is 10 year workmanship and 20 year manufacturer’s, and you can read the details on our warranties page.
If a bid is dramatically cheaper than the others, look at what is missing. Usually it is the tear-off, the fascia work, or the hanger spacing.
The one number that matters
Your house has a real number, and it is not the range above. Getting it takes an estimator on site with a measuring wheel, twenty minutes on your roofline, and a look at your fascia.
That visit is free, on site, and carries no obligation. You get the footage, the sizing recommendation, and the written breakdown whether you hire us or not.
High Point Gutter is family owned, founded in 2016 by Taylor and David Shores, with in-house installers out of Woodinville and Federal Way serving homeowners from Bellingham to Olympia. Licensed, bonded and insured, license #HIGHPPG841J1, certified Alu-Rex Master Installer, and 600+ Google reviews at 4.9 stars.
Call 425-449-6622 in Woodinville, (253) 785-6225 in Federal Way, or book a free gutter installation estimate. We send estimators, not salespeople, and you will get a straight number.
Always on Point.